Reader's Choice Awards: Thank you for your votes – we WON!

We have won for the last 16yrs so please help us win this year.

We’ve been voted Reader’s Choice for the past 16 years! Support us again this year by clicking here.

Rubber Roofing in Dayton, OH

Call Us Today

Request a Service

Loading form…

EPDM for the Flat Spots on Dayton's Older Houses


Rubber roofing in Dayton usually goes on the part of the house nobody looks at. Walk any block in St. Anne's Hill or Dayton View and look past the main roof: a back kitchen addition, a sleeping porch, a garage off the alley. Those nearly flat sections are where EPDM earns its keep, because shingles were never meant for a roof pitched that gently.


Rich Roofing & Services installs EPDM rubber on those low-slope sections, either as a new roof or as the replacement for a flat roof that has worn out. We're a family company that has worked in Ohio since 1965, out of an office in Troy, and we are a licensed roofing contractor.

This page covers new EPDM and full replacement. If you only have a drip over the back door, our crew handles that on the flat roof leak repair page for Dayton instead.


Contact us

What an EPDM Membrane Actually Is


EPDM is a synthetic rubber sheet, short for ethylene propylene diene monomer. It comes off the truck in wide rolls, so a typical porch or addition can often be covered with one piece or very few seams. Fewer seams means fewer places for water to find a way in.


The material stays flexible in cold weather. That matters in a town where the freeze-thaw swings of January are followed by spring thunderstorms off the river valleys.

There are a few choices to make before a roll gets unrolled:


Black or white: Black EPDM is the classic look and the most common. It soaks up sun, which helps snow clear faster but makes the roof surface hot in July. White EPDM carries a reflective top layer that keeps the surface cooler and usually costs more.

Fully adhered: The membrane is glued with bonding adhesive to a smooth board laid over the deck. It looks clean, handles wind well and is the usual pick on houses.

Ballasted: The sheet is laid loose and held down with river rock or pavers. It only works where the structure can carry that weight, so you see it on larger commercial roofs, rarely on a house.

Seams: Where two sheets meet, the overlap is primed and joined with seam tape, then rolled tight. Rushed seams are the reason most rubber roofs fail early.

Flashing: Walls, chimneys, plumbing vents and roof edges each get their own detail, from pre-formed pipe boots to termination bars along brick.

If your building is commercial and you are weighing heat-welded membranes instead, we explain TPO and PVC on our single ply roofing page for Dayton.

Where Rubber Roofing Fits Around Dayton


Most of the EPDM roofing we put down in the city lands on one of these:

Rear additions and porches

Early-1900s brick and frame houses in Belmont, South Park and Walnut Hills often have a low-slope rear roof tied into a two-story wall. The joint between that roof and the wall is the detail we spend the most time on.

Detached garages and carriage houses

A flat garage roof is a good candidate for a full tear-off and new rubber. It's a small job, and if the garage is being rebuilt from scratch, the work falls under new roof installation in Dayton.

Small commercial buildings

Corner storefronts and small shops in the Oregon District and along the older commercial streets often sit under low-slope roofs. EPDM is one option there, and our Dayton commercial roofing team looks at the whole building before recommending a membrane.

Roofs that drain to box gutters

Some older Dayton houses have built-in box gutters at the eaves. Where a rubber roof runs down to one, the transition has to be planned so the water ends up in the gutter and not behind it.

Why Dayton Owners Call a Troy Family Company

Our family has been roofing in the Miami Valley for 60 years and have been named a Reader's Choice winner 16 times. We're Latino-owned and Veteran-owned, and every person on the crew is background-checked before they set foot on your roof.


Estimates for Dayton rubber roofing are free and the pricing is upfront. You'll see what the job includes before anything is torn off.


Our office hours are Monday through Friday, 8 to 5. Call during those hours and you'll reach someone who can actually answer a question about your roof. You can also read what neighbors said on our reviews page.

Replacing a Worn Flat Roof with EPDM

A rubber roof replacement on a house is usually a short project, and so is most flat roof replacement on a porch or addition. Still, each step affects the next one.

Pulling Off the Old Layers

We remove the old rolled roofing, tar or tired membrane down to the deck. Whether a tear-off is needed at all depends on what's up there and how many layers are stacked on it, and we tell you that after looking.

Fixing Soft Decking

Old flat roofs often hide wet boards. We replace damaged decking and, where water used to pond, we can add tapered insulation so the new roof drains toward the edge or the drain.

Bonding the Sheet

A cover board goes down, then the EPDM membrane is glued in place and rolled out to remove air. Seams are taped, never just caulked.

Flashing Walls, Vents and Edges

Membrane runs up the wall, gets a termination bar and counterflashing, and pipe boots go over every vent. New edge metal closes off the perimeter.

Inspecting the Finished Roof

Before we pack up, we walk every seam and corner, clean the site and show you what was done. If you want a second look at the main roof while we're there, ask about a roof inspection in Dayton.

Rubber Roofing in Dayton and the Towns Around It


We cover the whole city, from Old North Dayton to the neighborhoods near Wright-Patterson, plus Kettering, Oakwood, Riverside, Trotwood, Huber Heights and Vandalia.


If you searched rubber roofing near me from a house off I-75 or US-35, you're inside our regular area. The same goes for anyone looking up EPDM roofers near me from the suburbs south and east of town.


Our contact page is the fastest way to set up a free look at your flat roof. If the main roof is the bigger worry, see our full roof replacement work in Dayton.

Dayton EPDM Questions We Hear Most


Contact us now
  • Can rubber roofing go on the main roof of my Dayton house?

    Only if that roof is nearly flat. EPDM is made for low-slope sections, so on a steep two-story roof shingles or metal are the better fit. Many Dayton homes end up with both: shingles above, rubber on the porch or addition.

  • Is black or white EPDM better for a house?

    Black is the common choice and handles winter well. White reflects more sun and keeps the surface cooler in summer, which can help if the flat roof sits over a bedroom. We'll show you both and price both.

  • How long does a rubber roof replacement take?

    A porch or small addition is often finished in a day or two. Larger roofs or ones with rotten decking take longer. Weather decides a lot, because adhesive needs a dry surface.

  • Do you repair leaks on EPDM roofs too?

    Yes, but that is a different job. If the membrane is still sound and you have one or two leaks, start with our flat roof repair page for your city. This page is about installing new rubber or replacing a worn roof.

  • What is the difference between EPDM and TPO?

    Both are single-ply membranes. EPDM is rubber and its seams are taped, while TPO is a thermoplastic with heat-welded seams. TPO shows up more on commercial roofs, and we cover it separately.

  • Can you put EPDM over my old flat roof?

    Sometimes, but we usually recommend a tear-off on older Dayton houses. The old layers tend to hide wet boards, and covering them traps the problem. We decide after looking at the roof in person.

  • Do you work on rubber roofing in Dayton for small businesses?

    Yes. Small shops and offices with low-slope roofs are a good match for EPDM. For larger buildings we compare it with TPO and PVC before recommending anything.

  • How do I get an estimate?

    Call (937) 335-7663 on a weekday between 8 and 5 or send a request online. The estimate is free, and we explain what drives the price, such as roof size, number of layers to remove and how many walls and vents need flashing.